SHR Settings

In this place you can easly tweak lot of things and controls of your phone.

SCREEN

Main screen is divided into few categories, which contain modules. Every SHR Settings module has specified task - control GSM antenna power, set actual time etc. 

**Phone**

SCREEN

*GSM*

In GSM settings you can turn off and on GSM module. After turning off antenna, whole GSM modem is turned off.

To list available providers, click on Operators button. Scanning can take some time. After while, list of operators should pop up.

SCREEN

You can't connect to operators marked as [forbidden]. After failed connect, message is displayed.

SCREEN

Selecting operator from list also changes modem registration mode to manual. It won't register to other network, even if some is available and has better signal strengh. To return to automatic mode, click "Automatic" button in operator list.

*Call*

You can decide, if your phone number should be displayed to other party. You can either depend on network decision ("By network") or force it manually ("Manual")

SCREEN

*SIM*

Here you can view some informations about your SIM card and clean phone and messagebooks.

SCREEN (?)

**Profiles**

SCREEN

*Profile*

Here you can select current profile, which device should use to determine ring tone etc.

*Current profile*

Here you can adjust properties of currently used profile. Available settings: ring tone, ring volume, ring vibration, ring loop, ring length, message tone, message volume, message vibration, message loop, message length.

To change ring tone, click on "Change" button.

SCREEN

To use your own ring tone, place it in /usr/share/sounds directory.

After selecting sid tune as ring tone, there are available controls to select tune number from file.

SCREEN

**Connectivity**

SCREEN

*WiFi*

With "WiFi radio" toggle you can set, if wifi module should be powered. WiFi radio has to be turned on before trying to connect to WiFi network.

*GPRS*

To enter APN, login and password fields, just click on actual value (default: "internet"). Keyboard will pop up.
NOTE: If you don't know APN, login and passwork, ask your provider.

SCREEN

To connect to GPRS network, just click "Connect" button. Entered values will be saved after successful connection.

SCREEN

*USB*

With this toggle you can switch USB port between device (Neo to PC) or host (device to Neo) modes.

*Bluetooth*

To power up Bluetooth module, swith "Bluetooth radio" toggle to "On". After that, "Visibility" toggle should arrive - set it to "On" if you want your FR to be visible by other Bluetooth devices on scanning.

**GPS**

SCREEN

*GPS*

By default, GPS is turned on only when requested (when you turn on TangoGPS, Navit, omgps or other GPS app). That state corresponds to "Auto" setting. After changing to "Manual", you can set it on all the time.

*GPS informations*

This page can be used to monitor GPS status. If some value isn't known, then "unknown" is displayed.

SCREEN

You can also view information about every visible satellite and check, which are used for getting fix. To do that, just click "Satellite details".

If you experience problems with GPS, turn it off, click "Remove AGPS data" and reboot your Neo.

**Date/time**

SCREEN

*Time*

Here you can view and set actual time. By default, time is just displayed, To adjust it, click on "Set time".

SCREEN

After finishing adjusting, click "OK" button.

*Date*

This module displays current date.

**Power**

SCREEN

*Battery*

This module displays informations about battery state - charge, voltage, remaining time etc. To update data, click "Update" button.

Here you also enable 500mA charging with dumb chargers.

*Display*

With this slider you can easly tweak backlight power.

NOTE: This setting isn't pernament over sessions. At boot backlight is set back to 100%.

*Power*

Here you can turn on or off automatic dimming or suspend after idle timeout (see: Timeouts module)

SCREEN

*Timeouts*

Here you can set up values of idle timeouts used by device. Timeouts are reached in this order: idle -> idle dim -> idle prelock -> lock -> suspend. Idle, idle prelock and lock aren't used by default in SHR at the moment.

**Services**

SCREEN

*Services*

Here is listed every interesting script from /etc/init.d/ directory.

SCREEN

After clicking on some, you can either start, restart or stop service and view result.

**Others**

SCREEN

*Splash*

With this selector you can select theme used by shr-splash at boot and shutdown. After clicking "Preview", selected boot image will be displayed for 5 seconds.

*PIM*

Module used by opimd developers. Doesn't have influence on behaviour of default SHR image.

*Userspace backups*

Here you can either archive or restore your files and configurations. (TODO)

SCREEN

*Image information*

SCREEN

This module contains basic information about installed image - name of buildhost, used revision, branch and time of build.